More Pics

Found this on the Internet today:

I think I hate the gloves. Hmmmm... have to work on that.

At the Fair

Fun with Flying:

Going to the fair last weekend was an experience to be sure. Originally I was supposed to fly from Las Vegas to Salt Lake and continue to Minnesota; however, when I got to the Las Vegas Airport, they changed my flight to go directly to Minneapolis. The consequence? Lost luggage. My bags got stuck along the way. I almost didn't get them in time. Fortunately, my cousin suggested that we go back to the airport and see if the bag came in on a later flight.

When we got to the Airport, my bag wasn't there. I talked to the baggage desk and to my disappointment, they had no idea where the bag was. About that time, I broke into tears. The poor customer service agent had no way of knowing I had just found out my mom was ill. Being the wrong person at the wrong time, I of course unloaded on the poor woman. To her credit she didn't send me away. She tried to comfort me and send me back to the hotel with an overnight kit.

The miracle happened when I turned around. I was just returning to my cousin when I spied a blue bag on the conveyor belt. I couldn't believe it was mine. I even pulled out my baggage claim ticket and followed the bag around the turn table while I counted off the numbers. It was my bag!!!!! Wonderful surprise! Shortly thereafter I received a call that my mother was alright as well.

In the morning, we arose to find the October sky filled with rain. We decided to go anyway! It was nice that the fur lining added to the warmth of the dress! Before I left home, I made a small shawl for around my neck in case it was cold. I'm happy I did. I was quite cozy wandering around the fair. There are more photos than the one below, but they are with my cousin. If and when I get them, I will post them.

Unfortunately, my girdle belt did not hold up during the fair. As you can see in the picture it is hanging askew. About five minutes before we took the picture, it got snagged and broke. I tucked it up for the length of this picture, then took it off and put it in my purse. I loved this dress and it worked wonderfully. It's a bit muddy, but I'm managing to clean it all up before the next fair.

Hopefully, I'll have more pictures soon.

Cheers!

Katie

Elizabethan gown hemming basics

Six Days Away!!!!

I am officially 6 days away from the Minnesota Renaissance Festival Trip. I'm afraid that finishing the dress cut into my blogging time. I can sew ten times faster if I'm not taking pictures of each step. Thus, I missed the tutorial on how to make a partlet and the under sleeves. I will do my best to make another set after the fair and put on the information; however the Lynn McMaster's pattern for the Partlet is really easy to follow.

Here is the finished dress: I still have to tack on the jewelry and hooks and eyes here or there, but for the most part it is done. Yay!!! The billament trim, the sleeve pull backs, the hat pin, and the necklace are both from Sapphire and Sage Jewelry. Rhonda is an absolute marvel and I highly recommend her work.

A Hem.....

As promised here is my short tutorial on hemming. I suppose it all begins with a good friend to help you. It is important that you don't guess on your hemming. Because of the farthingale and especially the bum roll, (see Simplicity Pattern 8881) your dress does not hang the same way that a normal dress hangs. Thus it is important for you to actually put on the dress (If you are the one wearing it) and have the hem figured for your body.

The Pitfalls:

Too low a hem: There is a tendency for people who make beautiful renaissance dresses to lower the hem to the ground level. Frankly this is how it should be. The Hem should just brush the floor so you glide across like on a cloud. Unfortunately this means that you will pick up every speck of dirt, leaf, branch, blade of grass, wood chip, and dust particle in the fair... not to mention the garbage. To put it simply, if your hem touches the ground at a renaissance fair you will end up with a very dirty skirt.

Too high a hem:There is an old costumer adage. If you are on a stage hem low. If you are on eye level, hem high... but not too high. Those who have ruined a dress due to the pitfall above sometimes over hem and end up with a six inch gap between the ground and their hem. This isn't a good combination either. First of all, you can see your shoes and ANKLES!!!

For the record ankles at this time period are far worse to show than your cleavage. So what's the right hem? I hem to the bottom of the netting on my farthingale. If you have no netting it is about three inches above the ground. From a spectator's standpoint your skirt will have the appearance of brushing the ground, without sweeping up the garbage in the fair.

Hem the underskirt.... then the over skirt: At times you will see this around the fair. This is my worst nightmare. In fact, I'm worried about it on the dress I'm making. However, there comes a time when you just have to trust your hemming buddy. In general you want to hem your over skirt a bit longer than your underskirt. Only by a half inch or so.... unless you are a pirate wench. :)

The Process:

Get Up High: I actually stand on a very sturdy coffee table, but in a pinch I've stood on a step stool as well. This is for the ease of your hemming buddy. It's a pain for them to sit all bunched over and being up high gives them a better perspective on the hem being straight.

What to Wear: You want to wear all of your costume. Not just all of the undergarments, you need to wear your bodice as well. Why? Because each piece of clothing effects how the garment hangs. When you add the bodice, make sure it is where you want the bodice to be. If you have not put in your hooks and eyes yet, have your hemming buddy do a double check to make sure that the skirt waist band is covered by the bodice. You should not see the skirt waist band at all. Also, make sure you wear the shoes that you will wear at the fair!!! This is very important! Every shoe makes you stand a different way.

How to stand: I know this is an odd topic. It's not really. After years in a costume shop, I have learned that where the arms are, makes a difference in the hem. So how do you stand? Stand straight, look forward not down, keep your arms to your side as much as possible.

Don'ts: DO NOT: hold your hands in the singer position. (cupped hands at your waist line) DO NOT: put your hands on your hips. (This will raise your shoulders and cause you to push down the sides of the dress. DO NOT: Bring your hands together in the front or the back. (This tilts the dress and will make the hem off in the front or the back)

Keep your eyes ahead:

Did I mention to look straight ahead? It is really difficult to do this, because this is your baby and you want the hem to lie right. At this point you will just have to trust your buddy. :) Looking down, tilts the dress slightly forward which will make your hem slightly higher in the front than in the back.

Hemming Buddy Duties:

The Hemming Buddy's job is to fold the hem so you have an even line all around the base of the dress. I prefer that my hem is folded under. That way I don't have to remove pins in order to hem the skirt. I always go back and add another row of pins to keep me sane while I am hemming.

Hem the underskirt then the over skirt. I actually flip the over skirt over my neck and shoulders for the underskirt hemming. Yes, this will make the underskirt slightly higher than the over skirt, but as I mentioned above, this is a preferable look.

Iron:

Once you have been pinned and you carefully remove the dress, you can hem your skirt and underskirt. My first duty when I hem is to press around the base of the pinned hem. I do this for two reasons. 1) If a pin falls out, I have a ironed crease to show me where the hem was supposed to go. 2) It is actually easier to hem the dress when you have ironed down the dress edge.

Machine or Hand Stitch:

There is a stitch on the sewing machine that hems your garment. It requires you to sew on the salvage of the hem and the needle jumps over to the folded back dress and picks up one stitch. In general I prefer the machine stitch, but I know that my over skirt is way too heavy for the machine at this point so I'm going to hem the good old fashioned way- by hand.

Remember the bottom of your dress is wider than the top of your dress, thus you will have extra fabric you have to deal with. This is done with neat folds in the hem. You need to be careful making the folds so they don't do damage to the line of the dress. Take your time and experiment.

The hem stitch I use is to pick up the fold of the hem with a needle using a whip stitch, then pick up a 1/2 centimeter piece of the main dress, I jump an 1/2 inch and repeat the process.

When you are finished it is important to iron down your hem again. Here are two pictures. it is obvious when you see the dress which has not been pressed after hemming.

Before:









After:










I will post pictures after the fair.

I still have a few things to do before I leave. I need to finish tacking the jewelry to the bodice. I need to put the hooks and eyes on the bodice and skirt to make sure they stay in place.

That's it! Thanks for visiting. If you have any questions I'd be happy to answer. :)

Cheers!

Katherine

And The Hat Goes On...

Getting a Bee in my Bonnet...

I do realize that in my last blog I promised a stimulating entry on Hemming. To be honest, hemming at the most is boring... at the least it is down right dull. I do know that there are people in the universe who don't know how to hem. I promise in the near future I will provide the how to... my way at least. :) For now... let's talk hats.

Upon researching on the Internet- a decent Renaissance Hat usually goes for $100.00 to near $500.00 depending on the materials. I have also found exquisite hats in the $1000.00s though I would never spend that kind of money on a hat. I have, however, purchased one for around $200.00, looked at it, and said I can make this. I'm not sure how the hat maker feels about that, but I did make quite a few changes to the style...including shrinking it down.

Because of the Utah Shakespearean Festival and the efforts of Sandra "Stig" Stiglinski, I have the basics of a millinery background. For laymen, Millinery is the art of hat making. I am in no means professional at this art- and it truly is an art. My stylings are passable at best. However, if you do not have hundreds of dollars to spend and you want a Tall Hat, perhaps this next bit of blog can help.

First questions:

QUESTION 1: Do I really need a hat?

SCA answer: Absolutely- and it better be period and no foreign materials.

My answer: Yes- you should have a hat, if you want to be period. If you don't- I suppose you don't need one. In the 16th Century hats were key. Everyone wore one from the lowest servant to the highest noble. Contrary to popular belief, no a circle of jewelry does not really count as a hat, nor does a circle of flowers. However, if you want to wear a circle of jewelry/flowers they're not going to keep you out of the faire. :)

For me, I like wearing a hat. I prefer the tall hats to the flat hats, mostly because I prefer making hats from buckram.


QUESTION 2: What is a tall hat and what is buckram?

Answer A. A tall hat was a hat worn mostly by men in the 16th Century. Pictures of women wearing Tall Hats do exist mind you they are just lesser than men. It is the precursor to what we call a Top Hat in the 21st Century. There were a variety of styles of tall hats. The German style tends to billow in the sides giving it a barrel quality. I've heard many call the English variety of tall hat an upside down flower pot with a brim. And, the Italian variety looks a bit squashed. The I prefer the tall hats with the sloping crown and the curving brim. By adding ostrich plume out the side and wearing it at a precarious angle on your head, it gives a startling look.

Answer B: Buckram is a stiffened fabric used for making hats. I will warn you that you need a very stiff buckram in order to get the crown of a hat to stand and not buckle. Heavy buckram actually looks like cross stitch fabric and is difficult to bend.


Getting Started: THE HAT BLOCK

To be honest, you can make a hat without a hat block. I have done it several times, but it is so much easier to do 90% of the work if you have something sturdy in the crown.

Making a Hat block is relatively easy. First you have to decide how you want the crown of your hat to look. Do you want it thick or thin? Do you want it to slope?

I want my hat to taper and I want it to tilt back on the brim. Because this is what I am looking for, I am going to buy a Styrofoam cone from the craft store. If you are after a thicker crown or the flower pot or barrel style, it might work to buy a plastic flower container from a nursery and clean it out. If it gives you the right slope to your crown and matches what you want, it will save you time and effort.

Taking the Styrofoam cone, I cut off the tip so the hat will be flat on top and not tilt. The base of the cone I cut at an angle to make the crown tip backward slightly. NOTE: You do not want too much of a tilt. It should be gradual.




Next, I shaved a few pieces off of the tip of the cone and added it to the back of my hat block. This makes the hat tilt back in the front but go straight up and down at the rear.






Third step, I pulled out my trusty packing tape and proceeded to wrap the Styrofoam until it felt tight and secure. I taped the sides, top, and bottom. Mostly so flakes of Styrofoam don't flake off all about my house, but also it will give some resistance to pins as I use this hat form.



Patterning the Hat:


Once I am happy with the look of my crown, I need to make a pattern. I used a light buckram for this part, however a good piece of butcher paper will work as well. Just make sure it is pliable.






Wrapping the pattern material around the hat block, I pinned the buckram in place. Once I have the entire crown covered, I cut off the excess buckram and unpinned my pattern.












Placing the hat form on a second section of buckram, I designed my brim. I drew both a rounded front and a pointed front, since I'm not sure what I want at this time. Pointed brims were more popular in the Victorian Era and it tends to cause problems when making the hat, so most likely I will end up with a rounded brim in the front.





Using the base of my hat form, I traced the opening for my hat. Upending my hat block makes it possible to make a pattern of the top of the hat as well.




The Buckram Base:



Patterns finished, I now move on to my buckram. I did have a problem with this-- I couldn't find any heavy buckram in all of St. George. Normally this would be a problem; however I discovered a few years back that you can use heavy needlepoint material doubled to get the same stiffness.





Doubling the needlepoint material, I cut out my patterns leaving room for seams. I left the pattern on the material and proceeded to cut my notches. Before I removed the pattern I folded back all the notches, so it would be easy to see where my seams need to go.




Next step: Pellon. Pellon is a very thin cotton batting that is fusible like interfacing. Some hat makers skip this step, but I find that Pellon is very good at giving a smooth sleek feel to your hat where you don't see seams. I cut the Pellon to match the pattern. (Leave no seam allowance)






Because I used a double thickness of needlepoint fabric, I need to stitch the two pieces together. Once finished, I ironed the Pellon onto the hat pieces and set the patterns aside.





For the next hour I stitched the hat together.

Start with the crown. overlapping the seam allowance, I used a simple stitch to seam the back.





I added the top of the crown, by taking only one of the notched tabs and sewing it inside the crown. As I finished one tab, I folded the second one down into the top of the crown. Because I used a hat form, it matched up perfectly.




Setting the crown down, I pushed the brim down on top of it. The tabs on the crown automatically fanned out and matched the brim. (It's important that you know where the front and back of your brim is supposed to be. You don't want to stitch and find out that you have the brim off center or even worse sideways. )




The easiest way to stitch on the brim is to turn the hat upside down and stitch through the corner of the brim and the crown. I made sure to catch the crown and the brim with each stitch. I finished by stitching the tabs down with a quick basting stitch along the brim.




Next, I needed to add wire to the brim. This will allow me to shape the hat's brim once it's covered and it will keep it's form. I chose to use a heavy aluminum wire, rather than craft wire. I have found in the past that craft wire does not have the strength I need to get the right curve.




Once I stitch the wire all the way around the brim, I can shape my hat and determine if I like the brim. (For the record, I did not like the point, unstiched the wire, and rounded the brim- It took maybe 15 minutes to make the change)




Fabric Time:

Once again, back to the pattern. Again I left room for the seam allowance; however, this time I did not prematurely notch the fabric. I find it too dangerous. that is how you end up with holes in your fabric. I cut two of my brim in my main fabric. I cut one of my crown in my main fabric and also one in my red lining. The top of my crown, I cut a bit larger in my main fabric than necessary as to give it a bit more play on the crown of the hat. I also cut one of the top of my crown in my lining fabric.

First step, sewing up the crown. With right sides together, I sewed a single seam down the center back of my hat. Next, I pinned right sides together of the crown top and the sides. Once sewn, I notched and pressed the seam open.

Again with right sides together, I attached the brim the same way that I attached the top of the crown-- notch, and press open.

Repeat the process with the underside of the brim and the lining.

(When sewing the lining things can get confusing, especially when you are dealing with the lining. Easiest way to do it: simply put the lining into the hat, place the fabric on the brim and fold the brim back and pin the lining. It is right sides together again, but it does play with your mind to do it.)

Getting out the Glue:

This is part of the reason I like Pellon. Taking tacky glue I put a dob on the top of the hat, and I also smeared it on the bottom of the crown where it attaches to the brim. I don't like putting it on the entire crown, because sometimes the glue can make the fabric wrinkle.

(NOTE: Do not do this if you are using a light fabric to cover your hat. The glue will show through and ruin the effect. If you are using a light fabric, you will have to stitch the fabric in place on your buckram form.)

Before putting the fabric onto the buckram, I put the hat block inside my hat form. As I put the fabric onto the prepared buckram, I pinned the fabric in place as I pulled it tight.

Once the crown was covered, I worked on the top brim. Again I pulled it smooth and pinned the fabric in place. Once completely covered and stretched, I left it for three hours to dry.

When I returned, I removed the pins and the hatblock and repeated the process with the brims underside. I started by simply pinning the lining in place. I don't bother gluing the lining inside. It will remain once I have the rest of the hat completed. Once I had the lining pinned, I put the Hat Block once again into the crown and pinned it in place. This would ensure that my lining would not slip out while I was setting the brim fabric. Again, I left the brim to dry for about three hours.

Needle and Thread:

The next step and possibly the most tedious, I needed to stitch the top brim and lower brim together. I did this by folding under the fabric and using tiny stitches to go all the way around the brim. If the fabric was too bulky to fold under, I trimmed it.

BEWARE TRIMMING TOO MUCH! You don't want to have a fraction of a centimeter to work with! Fabric does fray and it could ruin the look of your hat.

Voila!

I still most likely will add trim to my hat, but I don't have anything I like on hand to add right now. It does need a hat band and I need to add my feathered hat pin, but for now I have a hat!

TIP: Do not throw away your hat block! I keep my hat blocks for each hat to keep the shape of the hat when I travel. By sliding in the Styrofoam into the crown of the hat, you do not have to worry about the hat being squished on a plane or in the car.

Still to do:
Finish hemming the skirt and underskirt
Beading the underskirt (If I decide to go that way)
Adjust lacings on my bodice
Partlet
Hooks and eyes for skirt and Bodice

How to do a French Seam and finishing an Elizabethan underskirt without a waistband

Excuse me...Who owns this seam?:

While the creation of the French Seam is relatively obscure, the name however implies we know where the French Seam originated... that is unless you speak French. The sewing technique known as the French Seam in England is known as the Couture Anglaise in France. Thus- The English call it a French Seam and the French call it the English Seam. It seems that no one or everyone wanted to take credit for this tidy little stitch.

The French seam is a couture seam finish used in high-end clothing and is one of the most beautiful seams for any type of fabric—not just silks. It completely conceals raw edges and is sometimes used on the outside of garments. Since it ultimately has many layers, it is best used with lightweight and sheer silks such as three-ply or four-ply silk or silk crepe, crepe de Chine, charmeuse, chiffon, and georgette; however I use it any time I do not want a raw edge to appear.

It is very useful if you do not have lining. Since I do not want to line my underskirt, which would be about as pointless as lining a slip, I regularly use the French Seam to make the underskirt as well finished as the rest.

French Seams for Beginners...

To make a French seam, start by pinning the fabric with the wrong sides (the side of the fabric you don't want to be viewed) facing each other. Sew a seam 3/8 inch from the raw edge. At this point you should have a seam and raw edge on the side of the fabric that you want people to see.

It is my personal opinion that the seam should be clipped at this point, though many seamstresses disagree. I dislike raw edges and I tend to catch the raw edge in my second seam, so I use my pinking sheers to clip the fabric to 1/4 of an inch.

To make your life easier... I suggest ironing the pinked edges to the right or the left of the seam. Don't press open. This can cause problems. You want to press the raw edges together. It will give you a crisper line with which to work.

Second step: With right sides (the fabric you want to face out) together, fold the fabric along the seamline, sandwiching the raw edge seam created above. Manipulate the fabric between your fingers to bring the stitching of the seam to the very edge.




Keeping in mind that you have clipped the now covered raw edge of the first seam down to 1/4 inch, sew a second seam, encasing the pinked raw edge. Press the seam to one side; then press again from the right side of the garment.

This stitch, makes a lovely seam from both the inside and the outside of the garment.







The Underskirt for Simplicity Pattern 8881

The process for sewing the underskirt for 8881 is really well outlined by the actual instructions. Basically you have your front section and six side and back panels. The side and back panels all have the same lower part and differ only in a small section near the waist.

Using the French Seam I put the skirt together in this order. (Sorry I forgot to take pictures of most of the steps.)
1. If I have a lace overlay for the underskirt, I top stich it to the front skirt panel.
2. French Seam the Back Side, and Side pieces together.

To make my life easier, I sew the side pieces together, then attach it to the front panel using French Seams. When I first started making this dress, I would sew all the tops to the bottoms and I'd get them mixed up. Now, once I have a panel finished, I attach it to the skirt and save myself some anxiety.

3. French Seam the back sections together and sew the center back seam leaving 6-8 inches for an opening. ( At this point I leave the opening raw, and I'll come back to it later.)

4. French Seam the back to the skirt.

I do not use the waist band! For me, having the underskirt and the overskirt separate is a lesson in patience and dexterity. As you walk in a farthingale, your skirts tend to slip a bit- especially the underskirt, since it is not attached to the bodice. Last year I made the underskirt complete then attached the waistbands. It was bulky and messy. This year I'm doing away with the underskirt waistband. (I'll explain more below. For now let's deal with the raw edge opening)

It is perhaps not my most professional method of handling skirt openings. My intital instinct is to put in a zipper, but there is the danger in the SCA patrol catching sight of it. Thus, I usually opt to do a simple roll stitch where the skirt parts in the back. It will be covered by your overskirt and as you can see in the picture, I hand basted the underskirt opening down, so it won't get in the way of the overskirt. (Red dots in the picture below)




Doing a roll stitch is easy. Fold the fabric 1/4 inch. Now fold it 1/4 inch again and top stitch. Done!




Finishing the Skirt Without the Waistband:

To attach my waistbandless underskirt to my overskirt, I first baste stitched a 1'' seam around the top of the skirt. Pulling the thread I gathered the skirt opening until it matched the measurements of my overskirt.

Just like when I attached my overskirt to the waistband, I found the center of my underskirt and pinned it to the center front of my overskirt waistband.

I matched up the outside edges with the edges of my waistband. (Note: I did line these up about 1/2 of an inch from the outside edge of the waist band to hide any white showing) Pinnning the gathered underskirt in place, took a little patience, but in the end it looked lovely.

Because my sewing machine is already shuddering due to the bulk in the overskirt, I opted to whip stitch the underskirt in place. I did this for a second reason: The underskirt is usually the part of the dress which needs to be replaced first. By whip stitching the underskirt to the overskirt it makes it easily switched when the hem of the underskirt becomes worn.

A whip stich is when you loop the thread catching the top and the bottom of the fabric you are attaching. It doesn't look pretty, but it is hidden and ultimately (for me) forgivable. :)

At last the skirt has been sewn together; however the longest journey is still ahead. Now that the skirt is finished, hemming must occur. It's important that you have your hoop, bumroll, and both skirts completed before you hem. It is also a very good idea to have your bodice completed and that you wear the shoes you are going to wear to the fair on during the hemming process.

I'll talk about Hemming in my next blog entry in more detail.

As of right now my trip to the MRF is now a month away...

Skirt to do:

• Grommets,
• Hemming,
• Adornments for underskirt

Remaining items:
Bodice:

• Move corseting loops for new waist size (Yay)
• Add fabric cover
• Add Jewelry

Hat
Partlet